Turck 
Turck
Block Module for EtherNet/IP and CIP Safety Safe Digital Inputs and Outputs, Standard Universal Digital Channels, IO-Link Master Ports
SKU: 100000360 Type: TBIP-L4-FDIO1-2IOL
Available 3–5 business days delivery
€858.00 / pieces
€1,021.02 incl. VAT
Features
- • Ethernet/IP device
- • Integrated Ethernet switch
- • 10 Mbps/100 Mbps supported
- • 2 × M12, 4-pin, D-coded, Ethernet fieldbus connection
- • Glass fiber reinforced housing
- • Shock and vibration tested
- • Fully potted module electronics
- • Protection classes IP65, IP67, IP69K
- • 4-pin 7/8″ male connector for power supply
- • ATEX zone 2/22
- • CCC-Ex
- • Two secure digital SIL3-inputs
- • Two secure digital SIL3 channels as FDI or FDO (PP, PM)
- • Four secure digital SIL3 FDI channels
- • 2 IO-Link Master V1.1 slots Figure 1
General Information
| Mounting | 2 mounting holes 6.3 mm |
| Mounting | The data sheet serves as advance information. For |
| Mounting | definitive values see the corresponding product |
| Mounting | manual. In this respect, no liability for completeness |
| Mounting | and accuracy can be applied to the content of this |
| Mounting | data sheet. |
| Mounting | 7/8″ Power Supply |
| Mounting | Note |
| Mounting | Power supply cable (example): |
| Mounting | RKM43-1-RSM43 |
| Mounting | ID number 6914312 |
| Halogen free | yes |
| ETH1/ETH2NSMS | Green ON Ethernet Link (100 Mbps) |
| ETH1/ETH2NSMS | flashing Ethernet communication (100 Mbps) |
| ETH1/ETH2NSMS | OFF No Ethernet linkGreen On Active connection to a master |
| ETH1/ETH2NSMS | flashing Connection has been established but |
| ETH1/ETH2NSMS | not fully completed |
| ETH1/ETH2NSMS | Red On Communication Error |
| ETH1/ETH2NSMS | flashing One or more I/O connections |
| ETH1/ETH2NSMS | have the time-out status. |
| ETH1/ETH2NSMS | Red/Green Alternating Faulty self-test or configurationGreen On Diagnostics disabled |
| ETH1/ETH2NSMS | Green Flashing When used as a stand-alone |
| ETH1/ETH2NSMS | device: Device is in protective mode, |
| ETH1/ETH2NSMS | an EtherNet/IP™ client is accessing |
| ETH1/ETH2NSMS | the standard I/Os. |
| ETH1/ETH2NSMS | Red On Critical error |
| ETH1/ETH2NSMS | Red Flashing Correctable error |
| ETH1/ETH2NSMS | Green/ Flashing alternately Faulty self-test or configuration |
| ETH1/ETH2NSMS | Red |
| Ambient temperature | from -40 to 70 °C |
| Connector material | Nickel-plated brass |
| Material screw | 303 stainless steel |
| Dimensions (L x W x H) | 60.4 x 230.5 x 38.8 mm |
| Housing colour | Black |
| Storage temperature | from -40 to 85 °C |
| PWR | Green On V power supply OK |
| PWR | 1 |
| PWR | Off V power supply off or V undervoltage |
| PWR | 1 1 |
| Window material | Lexan |
| Altitude | Max. 5000 m |
| LED | Color Status Description |
| Housing material | PA6-GF30 |
| Material label | Polycarbonate |
| Degree of protection (IP) | IP67 |
| Degree of protection (IP) | IP69K |
| Degree of protection (IP) | IP65 |
LED Status I/O
| 12, 14 (IO-Link Port 1 and 2) SIO Mode | Green ON Digital Input signal is present |
| 12, 14 (IO-Link Port 1 and 2) SIO Mode | OFF No input signal |
| 0…3 | Green ON Channel active |
| 0…3 | flashing Self test |
| 0…3 | Red ON Discrepancy |
| 0…3 | flashing Cross circuit |
| 4…7 | Green ON Channel active |
| 4…7 | flashing Self test (input only) |
| 4…7 | Red ON Discrepancy, overload (output only) |
| 4…7 | flashing Cross circuit |
| 8…11 | Green ON Channel active |
| 8…11 | Red ON Overload (output only) |
| 8…11 | flashing Overload of supply |
| 8…11 | Green/Red alternating Channel active and overload of supply (input only) |
| 13, 15 | Green ON Digital input or output active |
| 13, 15 | Red ON Output active with overload/short circuit |
| 13, 15 | flashing Overload of supply |
| 13, 15 | OFF Input or output inactive |
Safety outputs (OSSDs)
| Actuator power supply | 2 A (resistive) |
| Actuator power supply | 1 A (inductive) |
| Output current in off state | < 5 V |
| Output current in off state | < 1 mA |
| Output current in off state | suitable for inputs according to EN 61131-2 Type 1 |
| Test pulse, typical | 0.5 ms |
| Test pulse, typical | 1.25 ms |
| Sensor supply | M12, 5-pin |
| Test pulse, maximum | 500 ms |
| Max. output current | The load must be mechanically or electrically inert to |
| Max. output current | tolerate the test pulses. |
| Max. output current | When configured as a PPM switching output the |
| Max. output current | negative pole of the load should be wired to the Mterminal of the corresponding output (Pin 2). |
| Additional Information | M12, 5-pin |
| Interval between 2 test pulses, minimum | 250 ms |
| Interval between 2 test pulses, minimum | Power supply V AUX1/T1 max. 2 A |
| Interval between 2 test pulses, minimum | Please consider derating as shown in figure 1 |
| Interval between 2 test pulses, minimum | C4, C5: FSO 0 max. 2 A; 500 mA per output |
| Interval between 2 test pulses, minimum | C6: V AUX1 max. 2 A |
| Interval between 2 test pulses, minimum | C7: FSO1 max. 2 A |
| Connectivity inputs | 2.5 ms |
| Output connectivity | 0.5 A, short-circuit proof, |
| Output connectivity | max. 2 A (resistive)/ 1 A (inductive) all std. outputs |
System data
| Web server | integrated |
| Transmission rate fieldbus | 10/100 Mbps |
| Service interface | Ethernet via P1 or P2 |
| Connection technology fieldbus | 2 × M12, 4-pin, D-coded |
IO-Link
| Transmission rate | 4.8 kbps (COM 1) / 38.4 kbps (COM 2) / 230 kbps |
| Transmission rate | (COM 3) |
| Number of channels | 2 |
| IO-Link port type | Class A and Class B |
| Frame type | supports all specified frame types |
| Supported devices | Max. 32 bytes in/32 bytes out per port |
| Power supply | Power supply V AUX1 max. 2 A |
| Power supply | Please consider derating as shown in figure 1 |
| IO-Link specification | V 1.1 |
EtherNet/IP™
| Addressing | acc. to EtherNet/IP specification |
| Quick Connect (QC) | (Not supported according to ODVA specifications) |
| Class 1 connections (CIP) | 3 CIP |
| Device Level Ring (DLR) | supported |
Safety Inputs OSSD
| Max. tolerance test pulse width | 1 ms |
| Low-level signal voltage | EN 61131-2 Type 1 ( < 5 V; < 0.5 mA) |
| Max. OSSD supply per channel | 2 A per C0, C1, C2, C3, |
| Max. OSSD supply per channel | 1.5 A at 70 °C |
| Max. OSSD supply per channel | Please consider derating as shown in figure 1 |
| High level signal voltage | EN 61131-2 Type 1 ( > 15 V; > 2 mA) |
| Interval between 2 test pulses, minimum | 20 ms at 1 ms test pulse width |
| Interval between 2 test pulses, minimum | 15 ms at 0.5 ms test pulse width |
Supply
| Power dissipation, typical | ≤ 5 W |
| Admissible range | 20.4…28.8 VDC |
| Electrical isolation | galvanic isolation of the voltage groups V1 and V2, |
| Electrical isolation | voltages up to 500 VAC |
| Supply voltage | 24 VDC |
| Connection technology power supply | 7/8″, 4-pin |
Safety Data
| PL according to EN ISO 13849-1 | Level e |
| Category according to ISO 13849-1:2008 | 4 |
| Useful Lifetime | 20 years (EN ISO 13849-1) |
| SIL according to IEC 61508 | 3 |
Safety Inputs floating/antivalent
| Test pulse, typical | 0.6 ms |
| Sensor supply | Power supply V AUX1/T1 max. 2 A |
| Sensor supply | Please consider derating as shown in figure 1 |
| Test pulse, maximum | 0.8 ms |
| Additional Information | No connection to external potential allowed |
| Max. cable length | up to 1 m |
| Max. loop resistance | < 150 Ω |
| Interval between 2 test pulses, minimum | 900 ms |
Standard/Directive conformity
| Directive | 2006/42/EC Machine Directive |
| Directive | 2014/30/EC EMC Directive |
| Directive | 2014/35/EC Low Voltage Directive |
| Shock test | acc. to EN 60068-2-27 |
| Approvals and certificates | CEUKCAATEX zone 2/22 |
| Approvals and certificates | CCC-Ex |
| Approvals and certificates | FCC statement, |
| Approvals and certificates | UV resistant acc. to DIN EN ISO 4892-2A (2013) |
| Vibration test | Acc. to EN 60068-2-6 |
| Vibration test | Acceleration up to 20 g |
| UL Certificate | cULus LISTED 21 W2, Encl.Type 1 IND.CONT.EQ. |
| Drop and topple | acc. to EN 60068-2-31/IEC 60068-2-32 |
| Note on ATEX/IECEx | The Quick Start Guide with information on use in Ex |
| Note on ATEX/IECEx | areas must be observed. |
| Electromagnetic compatibility (EMC) | Acc. to EN 61131-2 |
Power supply
| Supply voltage | 24 VDC |