Compact PROFIsafe / PROFINET Block I/O Module Safe Digital Inputs and Outputs

Name: Compact PROFIsafe / PROFINET Block I/O Module Safe Digital Inputs and Outputs
Brand: Turck
SKU: 100001826
Price: 913 EUR
Availability: InStock

SKU: 100001826 Type: TBPN-L5-4FDI-4FDX

Available3–5 business days delivery

€913.00 / pieces

€1,086.47 incl. VAT

These are our list prices.Get an individual quote within 24 h.

Request a quote

Data sheet

Features

PROFINET device
Integrated Ethernet switch
100 Mbps supported
2 × M12, 4-pin, D-coded, Ethernet fieldbus connection
Glass fiber reinforced housing
Shock and vibration tested
Fully potted module electronics
Protection classes IP65, IP67, IP69K
5-pin 7/8″ male connector for power supply
ATEX zone 2/22
CCC-Ex
Four secure digital SIL3 inputs
Four secure configurable digital SIL3 inputs or outputs Figure 1

General Information

Mounting	2 mounting holes 6.3 mm
Mounting	The data sheet serves as advance information. For
Mounting	definitive values see the corresponding product
Mounting	manual. In this respect, no liability for completeness
Mounting	and accuracy can be applied to the content of this
Mounting	data sheet.
ERR	Green On Diagnostics disabled
ERR	Red On Diagnostics enabled
Halogen free	yes
Ambient temperature	from -40 to 70 °C
Connector material	Nickel-plated brass
Material screw	303 stainless steel
Dimensions (L x W x H)	60.4 x 230.5 x 38.8 mm
Housing colour	Black
ETH1/ETH2	Green On Ethernet Link (100 Mbps)
ETH1/ETH2	flashing Ethernet communication (100 Mbps)
ETH1/ETH2	Off No Ethernet link
Storage temperature	from -40 to 85 °C
PWR	Green On V power supply OK
PWR	1
PWR	Off V power supply off or below defined threshold of 18 V
Window material	Lexan
Altitude	Max. 5000 m
LED	Color Status Description
Housing material	PA6-GF30
Material label	Polycarbonate
BUS	Green On Active connection to a master
BUS	flashing Ready
BUS	Red On IP-address conflict or Restore Mode or Modbus timeout
BUS	flashing Blink/Wink command active
BUS	Red/Green Alternating Autonegotiation or waiting for DHCP/Boot-P addressing
Degree of protection (IP)	IP67
Degree of protection (IP)	IP69K
Degree of protection (IP)	IP65

Safety outputs (OSSDs)

Actuator power supply	2 A (resistive)
Actuator power supply	1 A (inductive)
Output current in off state	< 5 V
Output current in off state	< 1 mA
Output current in off state	suitable for inputs according to EN 61131-2 Type 1
Test pulse, typical	0.5 ms
Test pulse, typical	1.25 ms
Input delay	M12, 5-pin
Test pulse, maximum	500 ms
Max. output current	The load must be mechanically or electrically inert to
Max. output current	tolerate the test pulses.
Max. output current	When configured as a PPM switching output the
Max. output current	negative pole of the load should be wired to the Mterminal of the corresponding output (Pin 2).
Additional Information	M12, 5-pin
Interval between 2 test pulses, minimum	250 ms
Interval between 2 test pulses, minimum	Power supply V AUX1/T1 max. 2 A
Interval between 2 test pulses, minimum	Please consider derating as shown in figure 1
Connectivity inputs	2.5 ms

LED Status I/O

0…7	Green On Channel active
0…7	flashing Self test
0…7	Red On Discrepancy
0…7	flashing Cross circuit
8…15	Green On Channel active
8…15	flashing Self test (input only)
8…15	Red On Discrepancy, overload (output only)
8…15	flashing Cross circuit

System data

Web server	integrated
Transmission rate fieldbus	100 Mbps
Service interface	Ethernet via P1 or P2
Connection technology fieldbus	2 × M12, 4-pin, D-coded

PROFINET

Addressing	DCP
Diagnostics	acc. to PROFINET alarm handling
Topology detection	supported
MinCycleTime	1 ms
Automatic addressing	supported
Media Redundancy Protocol (MRP)	supported
Conformance class	B (RT)

Safety Inputs OSSD

Max. tolerance test pulse width	1 ms
Low-level signal voltage	EN 61131-2 Type 1 ( < 5 V; < 0.5 mA)
Max. OSSD supply per channel	2 A per C0 to C7,
Max. OSSD supply per channel	1.5 A at 70 °C
Max. OSSD supply per channel	Please consider derating as shown in figure 1
High level signal voltage	EN 61131-2 Type 1 ( > 15 V; > 2 mA)
Interval between 2 test pulses, minimum	20 ms at 1 ms test pulse width
Interval between 2 test pulses, minimum	15 ms at 0.5 ms test pulse width

Supply

Admissible range	20.4…28.8 VDC
Power dissipation, typical	≤ 5 W
Electrical isolation	galvanic isolation of the voltage groups V1 and V2,
Electrical isolation	voltages up to 500 VAC
Supply voltage	24 VDC
Connection technology power supply	7/8″, 5-pin

Safety Data

PL according to EN ISO 13849-1	Level e
Category according to ISO 13849-1:2008	4
Useful Lifetime	20 years (EN ISO 13849-1)
SIL according to IEC 61508	3

Safety Inputs floating/antivalent

Test pulse, typical	0.6 ms
Sensor supply	Power supply V AUX1/T1 max. 2 A
Sensor supply	Please consider derating as shown in figure 1
Test pulse, maximum	0.8 ms
Additional Information	No connection to external potential allowed
Max. cable length	up to 1 m
Max. loop resistance	< 150 Ω
Interval between 2 test pulses, minimum	900 ms

Standard/Directive conformity

Directive	2006/42/EC Machine Directive
Directive	2014/35/EC Low Voltage Directive
Directive	2014/30/EC EMC Directive
Shock test	acc. to EN 60068-2-27
Approvals and certificates	CEUKCAATEX zone 2/22
Approvals and certificates	CCC-Ex
Approvals and certificates	FCC statement,
Approvals and certificates	UV resistant acc. to DIN EN ISO 4892-2A (2013)
Vibration test	Acc. to EN 60068-2-6
Vibration test	Acceleration up to 20 g
UL Certificate	cULus LISTED 21 W2, Encl.Type 1 IND.CONT.EQ.
Drop and topple	acc. to EN 60068-2-31/IEC 60068-2-32
Note on ATEX/IECEx	The Quick Start Guide with information on use in Ex
Note on ATEX/IECEx	areas must be observed.
Electromagnetic compatibility (EMC)	Acc. to EN 61131-2