HomePosition SensorsRadar Sensors100048852
TurckRadar Sensor – Level Control – Image 1
Turck

Radar Sensor – Level Control

SKU: 100048852 Type: LRS510-10-69-LI2UPN8-H1141/EU
Available3–5 business days delivery
€1,029.00 / pieces
€1,224.51 incl. VAT

These are our list prices.Get an individual quote within 24 h.

Request a quote
Data sheet

Features

  • Range: 10 m
  • Blind zone: 35 cm
  • Resolution: 1 mm
  • Cone angle of the radar beam: ±3°
  • Distance, level, volume or % output
  • Approved acc. to ETSI 305550-2
  • Male connector, M12 × 1, 4-pin
  • Operating voltage 18…33 VDC
  • Switching output switchable between PNP/ NPN
  • Analog output switchable between 4… 20 mA/0…10 V
  • Automatic current/voltage detection
  • IO-Link
  • 4-digit, 2-colored, 14-segment display
  • Housing is rotatable by 180° after mounting the process connection
  • Process connection G1"
  • Pressure resistance -1…16 bar rel.

Functional principle

FMCW radar stands for frequency modulated continuous wave radar. FMCW is the English abbreviation for Frequency Modulated Continuous Wave. Non-modulated continuous wave radars have the disadvantage that they cannot measure distances due to lack of time reference. Such a time reference for distance measurement of stationary objects can be generated by means of frequency modulation. Using this method, a signal is emitted which continually changes the frequency. A periodic, linear frequency which varies upwards and downwards is used to limit the frequency range and to simplify the signal evaluation. The factor for the rate of change df/dt remains constant. If an echo signal is received, then this has a runtime delay as with the pulse radar, and thus a different frequency that is proportional to the distance.

Electrical data

DC rated operating current Ie≤ 250 mA
Load resistance voltage output≥ 2 kΩ
Response time typical< 10 ms
Current output4…20 mA
Switching frequencyup to 10 Hz
Voltage drop at Ie≤ 2 V
Short circuit protectionyes/Cyclic
Polarity protectionyes
Output functionNO/NC programmable, PNP/NPN, analog
Output functionoutput
Load resistance current output≤ 0.5 kΩ
Output 2Analog or switching output
Communication protocolIO-Link
Residual ripple< 10 % Uss
No-load currentup to 100 mA
Residual current≤ 0.1 mA
Operating voltagefrom 17 to 33 V
Voltage outputfrom 0 to 10 V

Mechanical data

Display switch state2 × LEDs, Yellow
EMCEN 61000-6-2:2019
EMCETSI EN 301489-3 v.1.6.1
Vibration resistance20 g (10…2000Hz), EN 60068-2-6
MTTF178 years
Elektrischer AnschlussConnector, M12 × 1
Pressure resistance16 bar
Lensplastic, PEEK
Ambient temperaturefrom -25 to 65 °C
Shock testEN 60068-2-27
Process connectionG 1"
ApprovalscULus
ApprovalsCE
ApprovalsETSI
Storage temperaturefrom -40 to 85 °C
DesignWith display (integrated probe), LRS
Max. tightening torque of housing nut45 Nm
Housing materialStainless-steel/Plastic, 1.4404 (AISI
Housing material316L)/polyarylamide 50 % GF UL 94 V-0
Housing materialPEEK
Shock resistance50 g (11 ms)
Degree of protection (IP)IP67
Degree of protection (IP)IP69K
AbmessungØ 38 x 141.8 x 38 x 50.2 mm

IO-Link

Maximum Cable Length20 m
IO-Link port typeClass A
Communication modeCOM 3 (230.4 kBaud)
Function pin 4IO-Link
Function Pin 2Analog
Frame type2.2
Process data width80 bit
Minimum cycle time5 ms
Profile supportSmart Sensor Profile
Switchpoint information4 bit
IO-Link specificationV 1.1
Measured value information64 bit

Radar data

Edge lengths of the nominal actuator100 mm
FunctionRadar scanner
Resolution1 mm
Rangefrom 0.35 to 10 m
Hysteresis≤ 50 mm
Minimum switching range50 mm
Linearity error≤ ± 0.1 %
Opening angle6 °
Repeatability2 mm
Frequency rangefrom 122000000000 to 123000000000 Hz
Minimum measuring range500 mm
Output power EIRP10 dBm

Other

Process connectionG1
Housing materialEdelstahl
Housing materialKunststoff
Analog output4…20 mA
Connector typeM12
Switching outputSchließer/Öffner
Switching outputPNP
Switching outputNPN