Processor Unit – For the Connection of FCS and FCI Product Series Flow Sensors IO-Link Device with Relay Switching Outputs

Name: Processor Unit – For the Connection of FCS and FCI Product Series Flow Sensors IO-Link Device with Relay Switching Outputs
Brand: Turck
SKU: 7525102
Price: 281.9 EUR
Availability: InStock

SKU: 7525102 Type: FM-IM-3UR38X

Available 3–5 business days delivery

€281.90 / pieces

€335.46 incl. VAT

Data sheet

Features

• Relay output for flow, temperature and faults
• Adjustment of switchpoint, no teaching of flow boundaries (QuickTeach)
• LED band for indication of flow speed and media temperature
• Monitoring of operating and display range
• Detection of wire-break and short-circuit on the sensor side
• Standard IO or IO-Link operating mode
• Parametrized via pushbutton or software-supported via IO-Link

Functional principle

All non-Ex flow sensors from the FCS series (immersion sensors) and FCI series (inline series) can be operated with the FM-IM external processing unit. The flow module features four status LEDs the standard way. In IOL mode the current process signal is transmitted cyclically as a 10 bit-serial value. Parametrization is initiated either via pushbutton or software-supported via IOLink interface. The actual parametrization is then implemented via the tool-based DTM or IODD within the FDT frame PACTware™ or acyclically near the control via On-Request Data Objects (ORDO).

Mechanical data

Flow	yellow off Switching output flow [low]
Flow	on Switching output flow [high]
Flow	flashing Teach mode / display of diagnostic data
Flow	for specification see manual
Flow	Value 10 Bit (Bit 15 = MSB, Bit 6 = LSB) not assigned Out 3 Out 2 Out1
Flow	(Fault) (Temp) (Flow)
Temp	yellow off Switching output media temperature [low]
Temp	on Switching output media temperature [high]
Temp	flashing Teach mode / display of diagnostic data
Temp	for specification see manual
MTBF	126 Years
Mounting method	DIN rail mounting and mounting panel
Bit 15	14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Ambient temperature	from -25 to 70 °C
Design	Signal processor
PWR	green on Operating voltage applied
PWR	Device ready for operation
PWR	flashing Operating voltage applied
PWR	IO-Link communication active
PWR	(inverted flash with T on 900 ms and T off 100 ms)
LED displa	y
LED	Color Status Description
Housing material	Plastic, Polycarbonate/ABS
Fault	Red Off Switching output fault [high]
Fault	On Switching output flow [low]
Fault	(for error pattern in combination with LEDs see manual)
For detaile IM/FMX-IM IO-Link (Pr	d description of the display patterns and flashing codes see instructi
For detaile IM/FMX-IM IO-Link (Pr	ocess Data Objects)
Degree of protection (IP)	IP20
Abmessung	89 x 110 x 27 mm

Customizable output functions

Display switch state	NO/NC parametrizable (relay output error
Display switch state	monitoring only NC)
Switching characteristic	NO/NC
Switching voltage	< 250 VAC / 60 VDC
Error monitoring	relay output
Flow Monitoring	relay output
Electrical connections	5-pole removable reverse polarity protected terminal blocks
Type of fastening	screw connection
Temperature monitoring	relay output
Switching frequency	up to 10 Hz
Terminal cross-section	≥ 1.5…≤ 2.5 mm²
Switching current	up to 2 A
Switching power	up to 500 VA

IO-Link

Transmission rate	38.4 kBit/s (COM 2)
Communication modes	Tool based engineering via FDT / DTM,
Communication modes	IODD. Acyclic communication via On-Request Data Objects
Included in the SIDI GSDML	Yes
Communication channel	Jack plug COM (PC)
IO-Link specification	V 1.0

Electrical data

Measurement frequency	5 Hz (every 200 ms with software filter)
Sensor current limitation	approx. 110 mA
Repeatability media temperature	typical ± 1 K
Medium temperature	[°C] with the SET button temporarily
Medium temperature	pressed
Measuring accuracy media temperature	typical ± 7 K
Sensor current	≤ 35 mA
Sensor voltage	≤ 15 VDC
Frequency	from 40 to 70 Hz
No-load current I0	≤ 63 mA
Teach modes	QuickTeach; min/max adjustment. Teach
Teach modes	modes incl. DeltaFlow monitoring (teach
Teach modes	modes are automatically released with
Teach modes	the change of flow speed).
Input function	Connection of flow sensors (non-Ex sensors of the FCS/FCI product series only!)
Flow speed	[%] after min/max adjustment (permanent)
Flow speed	% after Quick-Teach (permanent)
Switchpoint hysteresis media temperature	2 K
Operating voltage UB	20…250 VAC
Operating voltage UB	20…125 VDC
Repeatability flow rate	typical ± 1 % (of full scale)
Power consumption	up to 4 VA